Read SDS and PIS before use
Do not mix with other chemicals including laundry powders and liquids
Always wear suitable gloves, body and eye protection
ALWAYS TEST FIRST - Because all surfaces are different, we always recommend that you perform a small test patch in an
inconspicuous area to ensure the products suitability to the surface and your expectations will be met.
Timber Instructions
1. Test first
2. Dilute 125-250g of Stanrose® Oxalwash into 5 litres of water. (Some timber applications may require higher concentrations)
3. Apply to surface with broom, brush, scourer or doodle bug.
4. Scrub with brush (medium to hard bristles) or doodle bug scourer and let dwell on surface for 5 to 10 minutes not allowing the surface to dry.
5. Remove and rinse thoroughly
6. Repeat process if required. Increase the amount of Stanrose® Oxalwash added to the water where necessary and start by testing first again.
Building & Construction Instructions
1. Test first
2. Dilute 125-250g of Stanrose® Oxalwash into 5 litres of water.
3. Apply to surface with broom, brush, scourer or doodle bug.
4. Scrub with a suitable agitation method (ie. scourer, brush, machine, doodle bug) and let dwell on surface for 5 to 10 minutes not allowing the surface to dry.
5. Remove and rinse thoroughly
6. Repeat process if required. Increase the amount of Stanrose® Oxalwash added to the water where necessary and start by testing first again.
Professional Carpet Cleaning Instructions
1. Test on a small inconspicuous area first to ensure suitability of this product on the surface.
2. Remove any debris or excess stain deposits
3. Dilute 50g of Stanrose® Oxalwash into 2 litres of water. You can make a weaker solution for less severe staining.
4. Spray or pour onto the fibre or fabric until wetted out. Do not over wet. Agitate gently if required.
5. Allow to stand for at least 5 minutes and for more stubborn stains allow 10-20 minutes dwell time.
6. Rinse & Extract with diluted pH neutral carpet/upholstery pre-spray and machine. For best results add ‘Plush – Carpet and Upholstery Rinse, Softener & Cleaner’ to your water in your machines solution tank. (If a machine is unavailable you can blot away with a damp clean white towel and then neutralise with Houdini Multi Task Spotter or Aussie Encappa diluted at 1:4. Blot away again with another damp white towel to remove all chemical and stain residue.)
7. Allow to dry. (You can assist drying by ensuring good ventilation and using an air mover)
8. Repeat process if necessary.
Tips for use on carpet:
Do not overwet carpet or upholstery with diluted solution.
Attend to spots and spills as soon as possible. Fresh spots are significantly easier to remove. Stains that are left too long or treated with the wrong chemical can become permanent.
Always do your stain removal working from the outside of larger stains to the inside. This prevents the stain from spreading.
Laundry Instructions
To remove rust and iron stains from laundry add 100-200g of Oxalic Acid to the hot pre-soak water. These quantities may be varied for different amounts of laundry to be soaked.
Oxalic Acid can be used on fabrics including cottons, poly cottons, silk and wool. Oxalic Acid is recommended for specialty stain removal when laundering all types of linen including uniforms.
Important
1. Do not use this product before reading and understanding the safety data sheet and Product Information Sheet.
2. Always wear personal protection equipment (refer to MSDS)
3. Oxalic Acid has the ability to dull or etch polished (shiny) natural stone surfaces.
4. Oxalic Acid is classified as hazardous under the criteria of Worksafe India.
5. Always pre-test in an inconspicuous area to ensure suitability before using this product.
6. Do not mix with any other chemicals
7. Some staining is permanent and can not be removed with a chemical. Replacement or restoration of surfaces may be required.